If you are a big fan of golf, we bet you know how helpful detaching your golf shaft from the clubhead is.
In fact, this hard affair isn’t a job for anyone, veterans in this field only.
Thus, we are here today to help you uncover how to remove golf club shaft properly.
Let’s glide through our article to catch useful steps for better preparation in your next golf rounds.
How to unfasten your club shaft properly?
- How To Assemble Golf Clubs
- How To Repair Golf Club
- How To Clean Golf Club Face
- What Each Golf Club Is Used For
- How to Increase Golf Club Speed
- What Is Loft On A Golf Club?
What Materials Need To Prepare
In order to commence the removal properly, you have to meet the necessary material list for reaching the best preparation, particularly:
- Torch (or heat gun)
- Heat resistant gloves (or wet paper towel)
- Utility knife (or box cutter)
- A vise
- Mineral spirits (optional)
Important Notes To Know Before Removing Golf Club Shaft?
Before moving on to the main part, we want to share some basic yet crucial notes for detaching the golf shaft.
Rule 1: Two Main Types Of Golf Club Shafts
There are two key sorts of club shafts in the current market: steel shafts and graphite shafts.
Although both of these shafts are made from different materials, how to unfasten them out of these clubs’ heads is based on a similar method, which we will mention in the following section.
Rule 2: Never Ensure That A Golf Club Shaft Could Be Saved Completely
A golf shaft is produced from long continuous fiber of carbon strands covered around a shaping mandrel.
An adhesive should be applied to stick the fiber coats together.
This same glue quite resembles the resin that is utilized to grasp the clubhead onto its shaft.
To separate the golf head of the shaft, you need to have using some heat.
Yet, using a heat source can also permeate or transfer into the club shaft and probably ruin the adhesive matrix gripping the golf shaft coats together.
Therefore, there is no guarantee of 100% of the safety for your club shaft when removing it from its club head.
Rule 3: The Necessity Of Equipping A Magnet For Shaft Removal
With this material, we will offer you a handy trick to remove shafts smoothly.
Using the magnet to stick to the hosel’s head to see how sticky it is, from that, you estimate relatively how hard and long to carry out the removal, particularly: if the magnet sticks, you will spend less time detaching the golf club shaft than the other case.
What is the cause for this affirmation? A magnet tends to stick to stainless steel and carbon, not on aluminum, titanium, or wood.
Thus, you can adjust your hand’s strength and movement properly on the key section when you turn and twist the club shaft out of the clubhead (that is mentioned in detail in Step 3 in the next part).
How To Remove And Assemble A New Shaft?
Once you have already finished equipping all the essential tools and vital notes, let’s find out the separation process.
The below section is a simple yet comprehensive guide to remove a club shaft in the best method.
Step 1: Detach The Ferrule
There is a mini plastic band on the hosel called the ferrule.
Using your box cutter (or a utility knife) is to cut a slit vertically on the ferrule at the link spot between a club head and its shaft.
With a plier or flathead screwdriver, pry that ferrule out of the club shaft and throw it away.
Step 2: Fix The Golf Shaft
Put the golf club in an equipped vise to fix its position for golf shaft elimination.
At this time, you should heed the direction of your club; we completely recommend your golf instrument now toward lying horizontally.
Keep in mind that somehow you should allow the vise to grasp the shaft’s clubs tightly to fend it off slipping out.
Don’t cover your clubhead entirely and expose the length of the shaft, approximately 8 inches.
Step 3: Melt The Adhesive Interior The Hosel
In this phase, you need to pay more attention to the hosel, which is the section where the golf shaft matches the golf club head.
Heat the adhesive interior of the hosel up by lighting the torch (could be propane one or use a heat gun) and put the heat source in the bottom of this hosel, which results in melting the adhesive inside.
When you use the heat to carry out this step, don’t forget to wear heat-resistant gloves (if you don’t have this kind of instrument, you can use a wet paper towel) to protect your hands from the heat source.
Then, grip the clubhead and lightly swivel it to commence unfastening on the hosel.
Please don’t turn it over with excess force; otherwise, your club shaft might break off or improperly bend the interior of the hosel.
Patiently and carefully loosen the clubhead until it comes free completely.
Step 4: Extrude Leftover Glue From The Hosel
Extrude the leftover glue from the hosel to offer a pleasant match to a new one.
You need to use some chunk of sandpaper with the size that relatively fits into the internal hosel.
Roll up and twist it to extrude loose adhesive.
To carry out this step more gently and clean the area thoughtfully, you should consider applying some mineral spirits (if you have).
If you still keep reading us until these final lines, we believe that from now on, you will be confident to try the edge-cutting shaft technology as well as adjust the shaft flexibly to your golf’s length.
As you have already learned how to remove golf club shaft, you can supersede the broken or bent shaft by yourself.
Believe us! This way will not run your money out to have a new golf club.
Thank you for viewing.
If you concur that our content is helpful, don’t forget to follow us and share it with others who have the same interest as you.
- 5 Golf Swing Basics – Keiser University College of Golf
- How to pick the right format for your golf outing